Beretta CX4 Bottom and Side Accessory Rail Kit Reviews

Back to Beretta CX4 Bottom and Side Accessory Rail Kit

Most Helpful Positive Review

13 out of 14 people found the following review helpful

4 out of 5

be aware

 

I would recommend the rail kit as fit and finish is excellent. You should be aware however that the "kit" only comes with one side plate and 4 screws. When you install the "kit" the screws on the off side do nothing but fill the holes they do not support the lower rail at all. So when you buy the "kit" be aware you have to purchase a second side rail to mount the lower rail onto your, most excellent, Beretta CX4.

Would you recommend this product to a friend? Yes
Most Helpful Critical Review

3 out of 3 people found the following review helpful

3 out of 5

Nice but not a complete kit

 

I purchased the Beretta CX4 Bottom and Side Accessory Rail Kit to add the short Vertical Commando Grip to the carbine. The "Kit" requires an additional purchase (my bad) of a side accessory rail to properly install the lower rail bracket to the other side of the firearm. $23.95 for a 2 3/4in piece of "Black Polymer" really? Beretta should really consider selling a complete kit for this purpose.

Would you recommend this product to a friend? Yes

Average Rating

4.3 out of 5
 

Based on 7 reviews

57% would recommend this item to a friend.

0% Rated this
0% Rated this
 
 
 
 

13 out of 14 people found the following review helpful

4 out of 5

be aware

 

I would recommend the rail kit as fit and finish is excellent. You should be aware however that the "kit" only comes with one side plate and 4 screws. When you install the "kit" the screws on the off side do nothing but fill the holes they do not support the lower rail at all. So when you buy the "kit" be aware you have to purchase a second side rail to mount the lower rail onto your, most excellent, Beretta CX4.

Would you recommend this product to a friend? Yes
 
 

7 out of 7 people found the following review helpful

5 out of 5

Nice

 

Fits perfectly. i would say only get this if you want a forward grip because the bottom rail hurts when the back of it hits your hand and its kinda just in the way otherwise.

 
 

4 out of 5 people found the following review helpful

5 out of 5

I NEEDED THIS BAD

 

I DIDNT KNOW HOW MUCH TILL I SHOT MY WONDERFUL BERRETA CX4

 
 

3 out of 3 people found the following review helpful

3 out of 5

Nice but not a complete kit

 

I purchased the Beretta CX4 Bottom and Side Accessory Rail Kit to add the short Vertical Commando Grip to the carbine. The "Kit" requires an additional purchase (my bad) of a side accessory rail to properly install the lower rail bracket to the other side of the firearm. $23.95 for a 2 3/4in piece of "Black Polymer" really? Beretta should really consider selling a complete kit for this purpose.

Would you recommend this product to a friend? Yes
 
 

2 out of 3 people found the following review helpful

5 out of 5

CX4 Bottom and Side Accessory Rail Kit

 

Nice accessory. Fits well. Might consider an extended side rail to accept a two slot extra magazine holder. There is really nowhere else to put one of those on this carbine.

 
 

2 out of 3 people found the following review helpful

3 out of 5

Good kit - but only if you already have one rail piece

 

This kit seems well made and I hope it will work as advertised but my CX4 came new without any rails and this kit only provides one. It will not mount with the single rail included in the kit. so you must have an existing piece or rail, or like me, you'll be forced to buy another piece.

Would you recommend this product to a friend? Yes
 
 
5 out of 5

Works on the CX4 and Benelli MR1 (RX4) BONUS!!!!

 

So I bought this kit when I purchased my CX4 new. Everything fits nice and secure. I'm very pleased with the fit and finish! A must for the CX4 owner!!! I liked it so much that when I purchased my Benelli MR1 (Beretta RX4), I wanted the kit for it too. I even tried my CX4 rail kit on my MR1 last night and dimensionally it will fit on my MR1. I mention this because Benelli USA is no longer supporting the MR1 parts wise... No tri rails in stock and no plan to order anymore in the future (in the US). Only drawback... the holes on the MR1 are not pre-drilled. So I will have that one hurtle. But I'm very pleased that I can count on Beretta to provide me what I need to make it happen. So I will be ordering a second kit. The bottom and side rail kit along with the Beretta CX4 Storm Side Accessory Rail Kit for my MR1. (The MR1 does not have any side rails from the factory.) Very pleased Beretta fan here!!!!

Would you recommend this product to a friend? Yes